ASTM F88 Untersuchung der Siegelfestigkeit flexibler Sperrschichtmaterialien durch 180°-Schälprüfung

How to Perform an ASTM F88 Peel Test on Medical Packaging

Written by Jonathan Camara

In the medical device and packaging industries, sterilization is a big concern. Whether a device is disposable or intended to be re-sterilized and re-used, all medical packaging must have seals strong enough to protect the sterility of the product while also being easy for healthcare providers to open. In order to ensure that packaging achieves this delicate balance, many manufacturers follow testing standards such as ASTM F88 to measure the tensile strength of the adhesives used in medical device packaging. This guide is designed to introduce you to the basic elements of an ASTM F88 peel test and will provide an overview of the equipment, software, and samples needed. However, anyone planning to conduct ASTM F88 testing should not consider this guide an adequate substitute for reading and following the full standard.

What Does it Measure?

ASTM F88 measures the peel strength of medical packaging in one of two peel configurations under normal ambient temperatures. It does NOT measure the peel strength of medical packaging with the medical device inside the packaging. Testing a packaged product is often useful for companies, but is considered outside of the scope of ASTM F88.

ASTM F88 is conducted on a universal testing machine (also called a tensile testing machine) at a rate between 200 and 300 mm/min (8 to 12 in/min). The standard calls for the calculation of two measurements:

Average Seal Strength - The average force per specimen adhesion width throughout the peel test.

ASTM F88

Maximum Seal Strength - The maximum force point recorded per specimen adhesion width that occurs during the peel test.

Both of these calculations are determined by analyzing data points acquired during each test. The standard recommends that these calculations be applied between 10% and 90% of the total acquired points. 

Bluehill Universal ASTM F88 test results

Tensile Testing System

A standard package for testing to ASTM F88 includes a 3340 series single-column tensile tester with a load cell capacity between 5 N and 5 kN (1.1 lbf to 1124 lbf). The 3340 series features a 500 Hz data acquisition rate and a 0.5% accuracy specification down to 1/200th of load cell capacity. For customers looking for higher force accuracy and data acquisition rates, Instron's 5940 series features a 2.5 kHz data acquisition rate and a +/- 0.5% accuracy specification down to 1/1000th of load cell capacity.

universal testing machine for ASTM F88

Both the 3340 and 5940 series testing machines can be purchased with Instron's Bluehill® Universal Software and Operator Dashboard. The Adhesives and Biomedical packages within Bluehill Universal come with pre-loaded test methods for many standards, including ASTM F88. For customers who need to meet 21 CFR Part 11 compliance, we offer ComplianceBuilder™ to track all additions, modifications, and deletions to all relevant Bluehill Universal files.

 Bluehill Universal Screen Shot 

Specimens and Specimen Measurement

Of the two testing configurations (T-Peel or 180° peel), there are three specimen holding methods: two for T-Peel and one for 180° peel. Each specimen is self-adhered to an alignment plate and then secured in an upper and lower grip for testing.

ASTM F88 gripping techniques

T-Peel "Technique A" - This configuration is a standard T-peel application where the adhered section is left unsupported while the specimen is under test.

T-Peel "Technique B" - This configuration is similar to Technique A; however, the adhered part of the specimen is supported by hand.

180° Peel "Technique C" - Technique C involves adhering one side of the specimen to a substrate or alignment plate for a 180° peel test. The side with the plate is inserted in the upper grip, while the other end of the specimen is secured in the bottom grip.

To ensure conformance with the standard, all specimens which need to be cut for testing shall be done so in accordance with ASTM D882, which is the testing standard for tensile strength and elongation of thin film. Specimens must be cut to a width of 25mm (0.984 in), 15mm (.5971 in), or 25.4mm (1.0 in).

Grips

There are two gripping solutions for this standard, depending on needs for ease of use, throughput, and the ability to offset alignment for 180° peel tests. In both cases, rubber-coated grip faces should be used so as to avoid tearing the delicate specimen. Jaw faces are available in many different sizes and are easily interchangeable.

Advanced screw side action grips provide a standard solution for each configuration outlined in ASTM F88. They are easily opened and closed with the use of screws on each side of the grip. In the case of 180° peel applications, either the upper or lower grip faces can be offset to account for the thickness of the substrate, or alignment plate.

Pneumatic side action grips provide an advanced solution for T-Peel specimens and improve throughput with the use of a pneumatic footswitch.

Both options can be fitted with specimen centering devices to ensure proper alignment for each test.

Variations in Data

Because ASTM F88 involves very low forces, test results can be easily affected by small details. For example, customers who prop up the tail of the specimen by hand (T-Peel Technique B) or use some other device to support the tail will see different results from those who test without providing any sort of tail support. Likewise, it is important to make sure that load cell cables and pneumatic grip hoses are properly clipped to the crosshead before testing, as hanging cords produce drag forces that can adversely effect test results. Though attention to detail and consistency is always important, the extremely low forces involved in ASTM F88 testing means that operators must be especially careful to control all possible adverse forces that might influence their results. 

Lastly, there will be variation between different brands of testing systems due to the different data acquisition systems used. This paper describes how Instron handles data rate and bandwidth, and how these settings effect peel test results. ASTM F88 grips

Related Literature

5940 Single Column Table Frames System Support

The System Support guide details the requirements, specifications, handling instructions, installation procedures, and maintenance details.

  • Manual
  • 5/3/2016
  • 1.2 MB

2712 Series Pneumatic Side Action Grips (2712-041, 2712-042, 2712-045, 2712-046)

Instron® 2712-04x Series Pneumatic grips, packed with features to enhance gripping performance, usability, and operator safety.

  • Products
  • 7/8/2009
  • 1.1 MB

2710-200 Series

Screw action grips provide a very simple and effective method for holding test specimens in a wide range of applications. The dual-action design of 2710-200 series grips means that jaw faces can be independently adjusted to accommodate different specimen thicknesses and geometries, ensuring that the line of tensile force remains concentric with the grip body. They can be equipped with a selection of optional jaw faces with a choice of surfaces including smoothground, rubber-coated, serrated and wave profile.

  • Products
  • 12/16/2005
  • 462.1 KB

ComplianceBuilder™ for Instron Software

For Medical Device and Pharmaceutical companies, records management compliance with FDA 21 CFR § 11 is non-negotiable. ComplianceBuilder™ (CB) is a stand-alone, add-on compliance solution that can be integrated with Instron’s Bluehill® Software to provide features necessary to meet the latest FDA 21 CFR § 11 regulations.

  • Products
  • 9/4/2018
  • 0.5 MB

Bluehill Universal Operator Dashboard

Instron® Bluehill Universal is the latest offering of material and component testing software. Built from the ground up for touch interaction, Bluehill Universal offers a new layout and enhanced features, giving users a simpler, cleaner interface for their testing system. The large touchpoints and intuitive touch gestures of Bluehill Universal offer a renewed, yet familiar software environment for all Instron users. Instron’s Bluehill Universal Operator Dashboard includes both the hardware and software necessary to get you on the path to simpler testing routines and refreshingly faster workflows.

  • Products
  • 2/7/2018
  • 0.9 MB